1. Exact fit, OE quality design ensures easy installation and precise operation
2. No special installation tools required
3. Rubber O-Ring piston seal forces the fluid efficiently through the valving components providing consistent performance
4. Patented Multi-Lobe Seal makes gas springs more tolerant to vibration and temperature extremes
5. Individually tested for performance and reliability

Editorial Review :

StrongArm gas charged lift supports are custom engineered and manufactured beyond industry standards to provide smooth operation and durability. The hardened chromium plated steel shaft is precision ground and polished for superior corrosion resistance and leak free sealing. The self cleaning piston assembly automatically opens during each compression cycle to keep the orifice clear of fluid contaminants and provide smoother operation and reliable performance. Most units also utilize StrongArm's patented temperature compensation module valve which ensures consistent operation even in extreme weather conditions. It does so by compensating for normal gas pressure changes caused by temperature variations. The metallic upper bushing is manufactured with bearing quality precision to provide exact fit with pistion rod and promote a long operating life.

Customer Review :

hood struts

product arrived quickly. Was easy to exchange out the old struts. Wish I had done it years ago.

Rating :

Hood stays open, like it should.

Great product, and great service, my hood now stays open without a stick, which is a pleasure.

Rating :

works perfectly

I got this for my 1999 Jeep Grand Cherokee Laredo, and it fit perfect. You only need a screwdriver to pry out a small clip. My hood only wouldn't hold up in cold weather, so I only replaced one strut, and that was plenty.

Rating :

90 second install -- works like a charm

The other reviews aren't kidding. It takes less than two minutes to swap out your old hood supports with these--all you need is a small flat-head screwdriver. On a Grand Cherokee, just pry up the retaining clips on the old ones and then snap these new ones over the existing ball joints on the vehicle. Done and done!

Rating :

Just pop them in - Don't know why I waited

This replacement is a no-brainer. The supports went in really easily. The hardest part was figuring out how to release the latches that attaches the support to the hood and chassis. After a minute fiddling with a screwdriver I figured it out then it took only minutes to replace both supports.

You will need a stick (or another person) to hold the hood open while replacing the supports, which in my case was no problem as I had been carrying a stick around for whenever I needed to hold the hood open anyway.

Rating :

More reviews...

Customer Review :

This tool is a beast

I bought this tool for a strut replacement that I was not ready to shell out $500 in labor for. The tool performed exactly as expected. The lesson learned was to plan tool placement on the springs so that you can use a ratchet for the tightening and loosening. The wrench worked fine but at 1/2 turn at a time it took a loooong time to tighten.

Rating :

Best and safest spring compressor ever used.

For the low purchase cost of this product I had worries about how well they would be built and how they would last. When I opened the carton to examine I was surprised at how robust they were made and when we used them I had confidence in their holding/gripping ability. I felt safe in the use of them and with the other manufacuturers pair that I threw away I never really felt as safe. Do I recommend them for the home mechanic, you bet I do and I will buy another pair if and when they ever wear out.

Rating :

They compress! Wow!

They work pretty much as advertised. I used them on a full 4 strut install, and these compressors never seized or jammed, nor were they ever too difficult to use with hand tools. I wouldn't say they were a joy to work with (only because compressing springs is rarely a joyful business) but they certainly didn't add to the frustration of the install.

Honestly, if you're considering cheaping out and going with a less expensive brand, don't; just get these. This is not an area you want to cheap out on - dealing with jammed compressors is not fun.

Rating :

Worked Perfectly

I used this to change the shocks on my wrx which the shop told me would be 1100 dollars and I did it for a grand total of 560. They are made of high quality materials and got the job done with ease.

Rating :

Coil Spring Compressors

Worked as advertized. Were a little difficult to get in the springs I was working on (Jeep Liberty), but I should have did more research on my part. Very well made product. They will last a lifetime.

Rating :

More reviews...

1. Extended length 16.45
2. Compressed length 10.25
3. This Auction is for a pair (2) units

Editorial Review :

BRAND NEW
GAS CHARGED LIFT SUPPORTS FOR YOUR REAR HATCH

FITS THE FOLLOWING VEHICLES
TOYOTA Celica GT GTS With OEM Spoiler and Rear Wipers

FITS THE FOLLOWING YEARS:
2000 2001 2002 2003 2004
00 01 02 03 04

Special Notes:
Extended length 16.45 Compressed length 10.25 (Please note that all supports are measured from center to center of each mounting point)


Made by Sachs know as ZF Trading and Stabilus, Piston know as Turbo Lift , or Strong Arm know as Motormite, Arvin, and Arvin Meritor a few of the worlds largest manufactures of Brand New gas charged Lift supports. Quality manufactures of lift supports for engine hoods (bonnets), hatchbacks, trunks, lift gates (liftgates), rear glass windows, tailgates and even car and truck seats.  If it is a lift support or strut, chances are they manufactured it.  These lifts or props supports feature Premium OEM materials and technology. All are new in the factory Package.

This Auction is for a pair (2) units; Not universals but made to fit the specific models listed above.

Easy to install, instructions are enclosed in each package.  Most installations simply require a small flat head screw driver and 10 minutes of your time.

Customer Review :

Great Value

This lift supports fit and work great in my 2000 celica gt. The installation is quick and pretty simple. Heating the bolts on the hatch was very helpful. The cylinders are a very good buy.

Rating :

PERFECT!

These worked perfectly for my 2000 Celica. Way cheaper than the $400 Toyota was going to charge me for the parts alone. And VERY easy to install. Just make sure you pay attention when you are taking the old ones off as to where the bottom piece goes..to the front or back. We installed it backwards at first so they didn't work and I was upset until I remembered that the support went to the back of the the 2 bolts that attach to the inside of the trunk. Felt stupid, but when we switched them around to the correct position, they worked perfectly!

Rating :

Lift Supports

Thank you for making this item available for toyotas. This would have cost us 110.00 each through toyota. They were pretty easy to install.

Rating :

WARNING - Before you start

Whatever you do, DO NOT try and remove the top swivel bolt without first cutting the arm away as shown in the video. Your only chance of getting the swivel bolt out in one piece is to use a 6-sided (NOT 12) 11mm box wrench. Using a lighter to heat up the bolt to melt the thread-locker is also a must.

If you do not do it this way -- like me (opps!), you will have to drill out the bolt.

It's not the end of the world, but it makes what should be a 15-20 minute repair job take about 1 hour.

Procedure for Drilling out Swivel Bolt

[1] Center punch the flat section of bolt that remains after you cut off the strut

[2] Use small 5/64" drill bit to start the hole and assure dead center, only drill about 1/8" of an inch with this bit

[3] Next move up to 5/32" drill bit, and slowly drill all the way through the bolt (about 5/8")

[4] Now move up to the final 17/64" drill bit, slowly drilling out the entire bolt to the end

If done properly, the residual bolt material will basically fall out and leave you just the threads. However, you might need needle nose pliers to pull some remaining pieces out

Lastly, have a 8 X 1.25 metric tap on hand to chase or dress the threads should it be necessary

Install new struts as per video.

Rating :

Celica Rear Hatch lift Supports -

Just purchased my Toyota Celica ... and the supports were shot. I ordered these supports from amazon and they were (pardon the pun) AMAZIN! LOVED THEM and they are absolutely great.

Rating :

More reviews...

1. Exact fit, OE quality design ensures easy installation and precise operation
2. No special installation tools required
3. Rubber O-Ring piston seal forces the fluid efficiently through the valving components providing consistent performance
4. Patented Multi-Lobe Seal makes gas springs more tolerant to vibration and temperature extremes
5. Individually tested for performance and reliability

Editorial Review :

StrongArm gas charged lift supports are custom engineered and manufactured beyond industry standards to provide smooth operation and durability. The hardened chromium plated steel shaft is precision ground and polished for superior corrosion resistance and leak free sealing. The self cleaning piston assembly automatically opens during each compression cycle to keep the orifice clear of fluid contaminants and provide smoother operation and reliable performance. Most units also utilize StrongArm's patented temperature compensation module valve which ensures consistent operation even in extreme weather conditions. It does so by compensating for normal gas pressure changes caused by temperature variations. The metallic upper bushing is manufactured with bearing quality precision to provide exact fit with pistion rod and promote a long operating life.

Customer Review :

Where's my order?

I ordered some parts and decided to see where they were inroute. The schedule said they were delivered today (jan. 4) I went outside and there they were! Ha Ha! I thought I heard a truck running around. The UPS men know me, and just dropped the package over the fence. Fine service etc. Now to see if the parts fit and work o.k. I will let you know if not.

Rating :

Well Worth It!!!

The installation was very fast and easy. I bought this both for the rear hatch and the hood. They work great and I ended up saving over $100 bucks if I would of taken it to the dealership. It was well worth it!

Rating :

Don't know why I waited

I lived with the tailgate on my Jeep Grand Cherokee dropping on my head for years whenever it gets cold out, until it dropped on my wife's head, knocked her down and hurt her hip when she hit the ground.

I got an ultimatum to have it fixed, but didn't want to pay the dealers $$$ to replace the support arms. I found the replacements on Amazon, read the reviews, found that it was not a difficult replace and invested the $40 to get the new supports. I should have bought a T-40 Torx bit from Amazon too, but got one at a local auto parts store for a couple bucks. It will help if you have a stick (or another person) available to force the tailgate fully open while you are replacing the supports, to get them aligned before inserting the screws.

What a difference. They went on really easily and although I can't recall how the tailgate opened and closed when new, the new supports actually allow the tailgate to almost pop open, and forces me to pull the tailgate down to get it to close. Now I need to be careful not to have the tailgate hit me on the chin when it comes open.....

While I was at it, I bought two Hood support arms and installed them too. Now I can get rid of that stick I have been carrying around for a couple years.

I can't believe I waited so long to replace the supports. For $60-70 and 30 minutes easy work, I fixed both problems that have been nagging me for years, and saved hundreds of dollars I would have had to pay a dealer.

Rating :

Lift support for the hood.

Great value allround. I replaced the Lift support for the hood on my jeep and hood stays up when im working on the engine. Im so happy easy to install and was delivered quick.

Rating :

works perfectly

I got this for my 1999 Jeep Grand Cherokee Laredo, and it fit perfect. Besides an ornary bolt, it was easy to install and took about 5 minutes. You do need a special star shaped bit to unscrew the bolt. My liftgate only wouldn't hold up in cold weather, so I only replaced one strut, and that was plenty.

Rating :

More reviews...

1. Exact fit, OE quality design ensures easy installation and precise operation
2. No special installation tools required
3. Rubber O-Ring piston seal forces the fluid efficiently through the valving components providing consistent performance
4. Patented Multi-Lobe Seal makes gas springs more tolerant to vibration and temperature extremes
5. Individually tested for performance and reliability

Editorial Review :

StrongArm gas charged lift supports are custom engineered and manufactured beyond industry standards to provide smooth operation and durability. The hardened chromium plated steel shaft is precision ground and polished for superior corrosion resistance and leak free sealing. The self cleaning piston assembly automatically opens during each compression cycle to keep the orifice clear of fluid contaminants and provide smoother operation and reliable performance. Most units also utilize StrongArm's patented temperature compensation module valve which ensures consistent operation even in extreme weather conditions. It does so by compensating for normal gas pressure changes caused by temperature variations. The metallic upper bushing is manufactured with bearing quality precision to provide exact fit with pistion rod and promote a long operating life.

Customer Review :

Easy to install once you have the correct female socket

These lift supports work well for my 1994 Jeep Grand Cherokee Laredo. In order to remove the old lifts and install the new ones, I needed an E8 female Torx star socket to remove and replace the arms. (It took me a while to find the right socket.) I got an 11 piece set from Amazon Anytime Tools 11 piece FEMALE E-TORX (star) SOCKET Set w/RAIL E4-E20 that included size E8.

Rating :

special socket

Got away with using a 1/4" socket and 4" extension instead of the special star-head driver tool

Rating :

Door, glass or hood. These work!

I bought 3 different sizes for my Jeep Grand Cherokee. These are pretty easy to replace, but they are really strong. I have no problem at all now with the heavy rear door. I actually just pop the handle and start to open the hatch door, then these take over and raise it up. Buy them without hesitation.

Rating :

Perfect Fit

These struts are identical to the original struts in my Jeep. Replaced within 10 minutes, although you do need a special socket to remove the E-type screws that attach the struts to the vehicle. Note that there are struts for the Left and Right side of the liftgate. DO NOT buy struts that claim to fit either side of the liftgate. I originally bought Sachs trunk struts from a local parts shop, which were supposed to fit either left and right sides - but I needed to use a few metal washers as shims so the door would close.


Rating :

Perfect fit Replacement Strut- do not be fooled by imitations

I have tried previouly to buy Hood/liftgate stuts, but without success of getting the proper items for my cars. These are perfect match to my 1996 Grand Cherokee. I had them installed in no time. There is a difference from left to right, so do not buy struts that claim to be universal. They will not work properly.

Great Product!!

Rating :

More reviews...